99% of the time the reason these guns don't work
-
- Global moderator
- Posts: 3575
- Joined: February 26th, 2006, 6:59 am
- Location: LAKELAND FL.
99% of the time the reason these guns don't work
99% of the time the reason these guns don't work is that they have not been cleaned, they are full of cosmoline , take the slide off and the grips and soak over night in a pan of kerosene,diesel fuel , or paint thinner ( do not soak the grips in the pan) spray down with brake cleaner or WD40 , whip it down and re oil and put a little grease on the rails
, then gun put gun back together ,
(there are other was to take cosmoline off of guns but it is must be fore you ever shoot the gun's and rifles)
NORM
, then gun put gun back together ,
(there are other was to take cosmoline off of guns but it is must be fore you ever shoot the gun's and rifles)
NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976
N.R.A. LIFE MEMBER 1976
-
- Forum supporter
- Posts: 1221
- Joined: February 5th, 2007, 8:52 pm
- Location: Portland Oregon
99% of the time the reason these guns don't work
Norm,
What do you use to remove it from wood?
G.R.
What do you use to remove it from wood?
G.R.
-
- Senior member
- Posts: 401
- Joined: March 17th, 2009, 8:16 pm
99% of the time the reason these guns don't work
Gunny, I've used Scott's Liquid Gold. But, I guess it would depend on the type of wood, soft, hard, dense grain what have you. Saw an old enfield SMLE HAD SO MUCH OF THE STUFF ON IT, it was a mess. Guy told me he was going to use Easy-off oven cleaner, also read that some where here. But, who ever it was was also stripping the stock too. I think that would be a little harsh. Maybe a plastic, throw away type putty knife and a heat gun set low. I'd have to see it. Mineral spirits??
-
- Global moderator
- Posts: 3575
- Joined: February 26th, 2006, 6:59 am
- Location: LAKELAND FL.
99% of the time the reason these guns don't work
GR
I always use ace hardware paint stripper on stocks, it will suck the oil and cosmoline and the finish off and out of a stock , but don't get any on you it will burn you like a house a fire, ( when I was 15 I work at an antique furniture repair store and that's what we used but it was a lot stronger stuff ) then with dish soap wash it of, I have even put some stocks in my dish washer depending how dirty they were ,
NORM
I always use ace hardware paint stripper on stocks, it will suck the oil and cosmoline and the finish off and out of a stock , but don't get any on you it will burn you like a house a fire, ( when I was 15 I work at an antique furniture repair store and that's what we used but it was a lot stronger stuff ) then with dish soap wash it of, I have even put some stocks in my dish washer depending how dirty they were ,
NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976
N.R.A. LIFE MEMBER 1976
-
- Global moderator
- Posts: 3575
- Joined: February 26th, 2006, 6:59 am
- Location: LAKELAND FL.
99% of the time the reason these guns don't work
this is pix of as is Martini Henry before
after striping
2 coats of ( BLO & Toung oil mix )
stocks back on rifle
NORM
after striping
2 coats of ( BLO & Toung oil mix )
stocks back on rifle
NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976
N.R.A. LIFE MEMBER 1976
-
- Forum supporter
- Posts: 955
- Joined: March 23rd, 2006, 8:40 pm
- Location: delaware/Virginia eastern shor
99% of the time the reason these guns don't work
by the way the MH stock looks even better in person,I was lucky enuff to see that and some of Norms other work when I was in Fla .last month.
99% of the time the reason these guns don't work
Remember even with soaking these guns there maybe some nooks and crannies that need special attention.On mine the trigger guard hinge pin would walk.I had to take it apart and clen it all out(hole,spring ,plunger) then alittle lube and everything was fine.
99% of the time the reason these guns don't work
Norm is correct. Clean it, then clean it again. I have seen the best and the worst of what a P-64 can look like. Mine are mint, but I have seen ones at gun shows that I wish I could buy parts off of!
My 1968 and 1975 are two of my favorite guns.
Fritzhund
"When the going gets weird, the weird turn pro"
Hunter S. Thompson: Fear and Loathing in Las Vegas
Hunter S. Thompson: Fear and Loathing in Las Vegas
99% of the time the reason these guns don't work
For wooden stocks/handguards, Easy Off oven cleaner works, but you have to clean off the cosmoline in layers. As I was going to refinish the wooden stocks/handguards, didn't care about the old finish. I did several SKS wooden stocks where the cosmoline was at least a half in thick. Especially some of the stuff from Century Arms in Vt.
Old plastic spatulas, plastic putty knives, etc all helped with the removal of the easy off/cosmoline slime. Wouldn't recommend this for your finer wooden stocks/handguards. Sgt P.
Old plastic spatulas, plastic putty knives, etc all helped with the removal of the easy off/cosmoline slime. Wouldn't recommend this for your finer wooden stocks/handguards. Sgt P.
Last edited by Sgt P on July 26th, 2009, 10:58 am, edited 1 time in total.
-
- Posts: 2
- Joined: June 2nd, 2009, 5:59 pm
- Location: Central South
99% of the time the reason these guns don't work
Hey Folks, I have reviewed the comments herein. Sound advice all. I have a 1973 that was packed with cosmo as stated. Took it apart and soaked overnight in diesel fuel. I am blessed to have compressed air. Blew everything out at least twice. Put it back together with Tetra Lube and Break Free. Was OK but thought something was lacking. (stiff in spots), Just received a can of Hoppes Moly Lube today. Took the slide off, wiped out old lube, add Moly to surfaces and rails and such. Put it back together. New Gun!!! On my mothers grave!! A new gun...... You might try it! Best wishes to all. Happy plinking!!!!! 1shot1xrag
99% of the time the reason these guns don't work
Remember to keep telling yourself - Cosmoline is our friend!
Seriously, I've used mineral spirits when removing cosmoline from all my previous milsurps. Its a bit safer to use than kerosene or diesel. It also works on wood. Use an old toothbrush to scrub the stuff out of hard to reach areas.
Seriously, I've used mineral spirits when removing cosmoline from all my previous milsurps. Its a bit safer to use than kerosene or diesel. It also works on wood. Use an old toothbrush to scrub the stuff out of hard to reach areas.
- Hobe Sound P.83
- Member
- Posts: 87
- Joined: May 27th, 2010, 10:27 am
- Location: Hobe Sound, Fla.
Re: 99% of the time the reason these guns don't work
Is that the Martini-Henry from the time of Zulu, Rorke's Drift, 1879? or is that one from pre-1888 before they went to the .303 Lee-Methford Rifle? Is she Fireable? Paul
CRY HAVOC! AND LET SLIP THE FALCONS OF ATLANTA!
-
- Global moderator
- Posts: 3575
- Joined: February 26th, 2006, 6:59 am
- Location: LAKELAND FL.
Re: 99% of the time the reason these guns don't work
Paul
that's a Nepal Francotte Henry, and I wouldn't shoot that one the action is to week,
I have five MH's 3 rifle's and 2 carbine's that I shoot , I also have 5 Gahendra Henry's that I also shoot
I just about have every untouched rifle that IMA sells and shoot all of them except the Francotte
http://www.ima-usa.com/index.php/cPath/ ... b60be962a9
NORM
that's a Nepal Francotte Henry, and I wouldn't shoot that one the action is to week,
I have five MH's 3 rifle's and 2 carbine's that I shoot , I also have 5 Gahendra Henry's that I also shoot
I just about have every untouched rifle that IMA sells and shoot all of them except the Francotte
http://www.ima-usa.com/index.php/cPath/ ... b60be962a9
NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976
N.R.A. LIFE MEMBER 1976
Re: 99% of the time the reason these guns don't work
I assume that the Martinis with the slip on recoil pads are the ones which you shoot most
often........
often........
-
- Global moderator
- Posts: 3575
- Joined: February 26th, 2006, 6:59 am
- Location: LAKELAND FL.
Re: 99% of the time the reason these guns don't work
royke
you got that right
NORM
you got that right
NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976
N.R.A. LIFE MEMBER 1976