Slide

Mods and Fixes by P-64 users...
Post Reply
Rudybetta
Posts: 6
Joined: September 22nd, 2012, 10:00 pm

Slide

Post by Rudybetta »

Replaced recoil spring w/ heavier one, but even when first trying to remove slide it was very difficult to do and even more so now. Not even close how easy it is in some videos. Any cures or suggestions ?
sharkey
Member
Member
Posts: 53
Joined: December 28th, 2011, 6:53 pm
Location: right here for now ... SEPA

Re: Slide

Post by sharkey »

Eat Wheaties ?

Sorry I had to ....
If this is you first pistol that breaks down like this it takes time and a kinda learning curve I found ..... Yes the heavier spring will be more difficult to break down ......

I pull mine apart in about 5 seconds now and I'm not in a hurry ..... Just rushed ..... Slow is Fast in a LOT of things in life
Cum catapultae proscriptae erunt tum soli proscripti catapultas habebunt.
User avatar
Curly1
Elite member
Elite member
Posts: 2529
Joined: September 20th, 2011, 11:35 pm
Location: Upstate NY

Re: Slide

Post by Curly1 »

The spring may not be ground flat on the end like the original, compare them.

My 22lb spring isn't ground flat and yes it is a little difficult to get back on but I use my shooting glove to get a good grip on it.
Laugh Hard and Often.

Gary
EGL
Junior member
Posts: 10
Joined: March 4th, 2013, 3:20 pm

Re: Slide

Post by EGL »

I have a new to me, 1975 P64. It is a beauty. But, the double action trigger pull required two fingers. Without having fired the P64 I have read all the great posts on recoil and hammer spring issues. So, I ordered and installed the recoil and hammer kits and chose the 18 lb hammer spring and the 18 lb recoil springs. (Interesting learning curve there) I also ordered and installed the blued magazine release device made by Matt Z. Great release and it works just fine. But wait...there's more!

After having installed the new 18 lb recoil slide spring without filing off the ends of the spring I had a duhhhh moment. BIG MISTAKE! Now I cannot remove the slide.
I have eaten my Wheaties etc. and I sure do want to remove the slide and flatten the spring ends to prevent this again. At the moment I have still not been able to remove the slide.
Any thoughts?
Ed :oops:
User avatar
Curly1
Elite member
Elite member
Posts: 2529
Joined: September 20th, 2011, 11:35 pm
Location: Upstate NY

Re: Slide

Post by Curly1 »

ED,

Have you tried to remove it after firing?

Try using snug fitting leather gloves to get a good grip on it and crank it back as had and fast as you can and lift up on it as soon as it is racked back in the same motion.

I also use a thin strip of wood to hold the trigger guard down so I dont have to deal with holding that off to the side.
Laugh Hard and Often.

Gary
User avatar
lklawson
Senior member
Senior member
Posts: 469
Joined: February 19th, 2011, 8:39 pm
Location: Huber Heights, OH
Contact:

Re: Slide

Post by lklawson »

EGL wrote:After having installed the new 18 lb recoil slide spring without filing off the ends of the spring I had a duhhhh moment. BIG MISTAKE! Now I cannot remove the slide.
I have eaten my Wheaties etc. and I sure do want to remove the slide and flatten the spring ends to prevent this again. At the moment I have still not been able to remove the slide.
Any thoughts?
Ed :oops:
Use a 2x4.

Put the 2x4 on the ground. Grasp the pistol in a standard pistol-grip. Place the top of the slide, just above the muzzle, against the 2x4. Push down. When the slide has moved as far back as it can go, while maintaining pressure on the gun, grasp the back of the slide and pull up and away relative to the gun.

Peace favor your sword,
Kirk
The Cheapskate's Guide to Gun Cleaning and Maintenance - "You shouldn't have to spend thousands of dollars on expensive gun cleaning an maintenance products. Find out how to save money with inexpensive alternatives that work just as well."
EGL
Junior member
Posts: 10
Joined: March 4th, 2013, 3:20 pm

Re: Slide

Post by EGL »

High Curly1 and thanks for the quick response. I have not fired the gun yet. I'm anxious to do so. That will help as you suggested I'm sure. I have used my gloves too. They help a lot since during this whole process I nicked the end of my dominant hand thumb and it is giving me fits. Also good idea on the wood chip to keep the trigger guard from closing. That has happened several times during this struggle. :P I will continue to use all of these ideas as I learn more about how to use and maintain this great hand gun.
Again thanks for the great ideas.
You folks are great.
Regards,
Ed
EGL
Junior member
Posts: 10
Joined: March 4th, 2013, 3:20 pm

Re: Slide

Post by EGL »

lkLawson, wow the ideas are popping here on the forum. Will probably use the 2 X 4 idea before all is done.

Thanks a bunch.
Ed
EGL
Junior member
Posts: 10
Joined: March 4th, 2013, 3:20 pm

Re: Slide

Post by EGL »

I have used the 2 X 4 method with gloves and it worked like magic. I just wasn't strong enough or coordinated enough to do it without an assist. Thanks guys for the help. The P64 slide mounts and dismounts real slick. Papa like! :P This completes another step on all of my prepper activities.
Just got my ALICE ruck sack and frame today and sorting through how to arrange all of my bug out gear for me and my wife. That is a topic for another thread.

Best regards to everyone and the good advice.
Ed
User avatar
Curly1
Elite member
Elite member
Posts: 2529
Joined: September 20th, 2011, 11:35 pm
Location: Upstate NY

Re: Slide

Post by Curly1 »

Godd to hear you got it don, Ed.

Give us a range report and show us some P64 porn :)
Laugh Hard and Often.

Gary
EGL
Junior member
Posts: 10
Joined: March 4th, 2013, 3:20 pm

Re: Slide

Post by EGL »

I sure will and again thank you for the help and a big thank you to the forum.

EGL
Rudybetta
Posts: 6
Joined: September 22nd, 2012, 10:00 pm

Re: Slide

Post by Rudybetta »

Thanks to Curly1. Instead of using shooting gloves to grasp the slide to pull back I used those rubber oven gloves and you can really grab ahold of it now but it's still not easy. Thanks
User avatar
Curly1
Elite member
Elite member
Posts: 2529
Joined: September 20th, 2011, 11:35 pm
Location: Upstate NY

Re: Slide

Post by Curly1 »

Your welcome Rudy.

That is an option I didn't think of.
Laugh Hard and Often.

Gary
Post Reply