I just bought a CZ82 from a buddy of mine and while playing
with it, I find it won't fire in DA. When the trigger is pulled, the hammer
goes all the way back, but won't release. Anybody have any ideas
what might be wrong? Thanks for any info.
Denny
CZ82 DA Problems..........
- lklawson
- Senior member
- Posts: 469
- Joined: February 19th, 2011, 8:39 pm
- Location: Huber Heights, OH
- Contact:
Re: CZ82 DA Problems..........
Make sure the internals are cleaned. Might be some detritus preventing the trigger from traveling far enough to break.
Peace favor your sword,
Kirk
Peace favor your sword,
Kirk
The Cheapskate's Guide to Gun Cleaning and Maintenance - "You shouldn't have to spend thousands of dollars on expensive gun cleaning an maintenance products. Find out how to save money with inexpensive alternatives that work just as well."
Re: CZ82 DA Problems..........
Have torn it down and found the sear spring broken.
Have a new one on the way. I've read where the
disconector can cause the DA issue, but this gun looks
like it just left the arsenal. I don't see any wear any
where on it.
Denny
Have a new one on the way. I've read where the
disconector can cause the DA issue, but this gun looks
like it just left the arsenal. I don't see any wear any
where on it.
Denny
- lklawson
- Senior member
- Posts: 469
- Joined: February 19th, 2011, 8:39 pm
- Location: Huber Heights, OH
- Contact:
Re: CZ82 DA Problems..........
Strangely enough, that does happen. The spring probably was defective from the factory and broke within a few cycles; maybe while being dry fired.
Peace favor your sword,
Kirk
Peace favor your sword,
Kirk
The Cheapskate's Guide to Gun Cleaning and Maintenance - "You shouldn't have to spend thousands of dollars on expensive gun cleaning an maintenance products. Find out how to save money with inexpensive alternatives that work just as well."
Re: CZ82 DA Problems..........
I replaced the spring and the same thing happens.
Now it won't fire in SA. When I pull the trigger, the
seems to drop on a half cock position. The DA will
work with the trigger guard off, but when it's in
place, the hammer won't drop in DA. Just the same
as when I started to work on it. I think its a piece
of junk.
Denny
Now it won't fire in SA. When I pull the trigger, the
seems to drop on a half cock position. The DA will
work with the trigger guard off, but when it's in
place, the hammer won't drop in DA. Just the same
as when I started to work on it. I think its a piece
of junk.
Denny
Re: CZ82 DA Problems..........
Well, I finely got it to work. Ordered a new sear from CZUSA and installed
it this morning. Works like a charm now. After tearing it down and back
together 4or5 times, it's really not that hard to do. Just glad it's done.
Denny
it this morning. Works like a charm now. After tearing it down and back
together 4or5 times, it's really not that hard to do. Just glad it's done.
Denny
Re: CZ82 DA Problems..........
Glad you got it working. I have a CZ 82. I liked it enough that I bought 4 CZ 83's for my kids in 380. I had one problem with mine. While cleaning it, the pin for the trigger guard pin fell out. The trigger guard fell out & the slide release spring came out. WHAT A PAIN to get it back in! Someone here designed a new one that is easier to use. Have fun with your gun!
Re: CZ82 DA Problems..........
Good news and great experience gained in solving this problem.
Laugh Hard and Often.
Gary
Gary
- Hurryin' Hoosier
- Forum supporter
- Posts: 166
- Joined: July 16th, 2013, 9:08 am
- Location: Columbus, Indiana
Re: CZ82 DA Problems..........
The trigger guard axis pin (I think it's called) is notorious for doing this. Usually, they won't fall out if you put the trigger guard "up" before removing the grips. What you might want to try, though, is putting one end of the pin just barely into a vise and squeezing the Pelosi out of it. I did that with one of mine and it made the end of the pin sufficiently out-of-round to make for a snug fit.jemsj4 wrote:Glad you got it working. I have a CZ 82. I liked it enough that I bought 4 CZ 83's for my kids in 380. I had one problem with mine. While cleaning it, the pin for the trigger guard pin fell out. The trigger guard fell out & the slide release spring came out. WHAT A PAIN to get it back in! Someone here designed a new one that is easier to use. Have fun with your gun!
"I'm just a poor white man, trying to make my way in the world." - Officer Andy Renko, "Hill Street Blues"