p-64 firing pin

jeepman3366 · Post by **jeepman3366** » August 2nd, 2009, 8:19 pm

Where can i get a firing pin for my p-64 ? ???

eagle71 · Post by **eagle71** » August 30th, 2009, 8:11 pm

Great question jeepman - I'd like to get a spare myself! I've searched online but no joy. I saw a Walther site, but doubt they're interchangeable.

Any of you experienced P-64 guys out there have any advice?

Sgt P · Post by **Sgt P** » August 31st, 2009, 11:13 am

Hey Guys,
I am checking with a Polish military friend to see if he can export a few P-64 firing pins and springs. I do not know if they would allow these parts into the US without an import license.

I know that we had problems bringing in German made Walther P-22 parts when they first came out. ::) Sgt P.

eagle71 · Post by **eagle71** » August 31st, 2009, 9:47 pm

Thanks, Sgt P!
If/when you're able to get some firing pins from your friend, you'll have at least two buyers

blinddog · Post by **blinddog** » September 2nd, 2009, 10:30 pm

If you guys find where some are, post it, because I would like a couple myself.

jeepman3366 · Post by **jeepman3366** » September 27th, 2009, 8:21 am

any body know where to get a firing pin for my p-64 ?

Post by **normsutton** » September 27th, 2009, 8:54 am

good luck finding one

NORM

jeepman3366 · Post by **jeepman3366** » November 9th, 2009, 7:46 pm

still looking for a firing pin any help out there ?

Sgt P · Post by **Sgt P** » November 10th, 2009, 1:10 pm

Guys,
Have been working the firing pin issue with my Polish Army friend. So far he has not replied back as I believe he got redeployed back over to Afghanistan. When I hear back from him, I will let you all know. Also have to BATF/Customs question about how many I could import here into the US without a license.
Sgt P.

rottenrick · Post by **rottenrick** » November 10th, 2009, 1:41 pm

Know anyone with a programable lathe??

Sgt P · Post by **Sgt P** » November 11th, 2009, 12:03 pm

I would love to get some titanium from Halprin Titanium up in MA and see if one of the local machine shops could copy my firing pin. Do not know the hardness of the P-64s firing pins but I am sure one of them could find out. Norm any idea?
Sgt P.

Post by **normsutton** » November 11th, 2009, 2:11 pm

Sgt P

just go to ace hardware and get some stainless steel rod and turn that , I made a firing pin out of it for a snider carbine, and holding up just fine , I suspect the tips were burned off the firing pins from using wolf ammo, or weren't using snap cap's,
NORM

hangfire · Post by **hangfire** » November 19th, 2009, 2:53 pm

Guys there is a good article entitled "Replacing Missing Firing Pins" written by a gunsmith at:

http://www.gunreports.com/special_reports/

It's not specific to the P-64 and is geared more to the person with some machinist skills but might be helpful. hangfire

ronbuick · Post by **ronbuick** » December 5th, 2009, 11:12 pm

Has anyone come up with the firing pin solution on where to buy?? on that note how good are the firings we have in our P-64's, thanks guys.

Ron

Post by **normsutton** » December 29th, 2009, 6:19 am

Ron

they are good firing pins , the only problem that I have seen with them is when someone has fired wolf ammo in the gun , and burnt the tip off

NORM

The Unofficial P64 Resource Forum