p-64 firing pin

Mods and Fixes by P-64 users...
normsutton
Global moderator
Global moderator
Posts: 3575
Joined: February 26th, 2006, 6:59 am
Location: LAKELAND FL.

p-64 firing pin

Post by normsutton »

brock123

S&B doesn't make a HP bullet I don't think , but S&B is good ammo that company loads for 9x18 cartridge's for Winchester

NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976

ImageImage
brock123
Member
Member
Posts: 53
Joined: January 10th, 2010, 10:32 pm
Location: Lansing, MI

p-64 firing pin

Post by brock123 »

s&b was silver bear sorry wasn't thinking ;-)
normsutton
Global moderator
Global moderator
Posts: 3575
Joined: February 26th, 2006, 6:59 am
Location: LAKELAND FL.

p-64 firing pin

Post by normsutton »

brock123
silver bear is good ammo 95 grn . HP may jam a bit tell it gets broke in or high polish the feed ramp, these guns were deign to shoot ball in them not HP , no military is

NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976

ImageImage
brock123
Member
Member
Posts: 53
Joined: January 10th, 2010, 10:32 pm
Location: Lansing, MI

p-64 firing pin

Post by brock123 »

Yeah I am planing on cleaning, polishing the ramp and replacing the springs right after I get it. Wish I could find a reasonable FFL a little closer to home. I checked a few place and they all wanted 75 bucks. The place where I grew up is only 25 but 2 hours away.
irishbob979
Member
Member
Posts: 74
Joined: October 12th, 2009, 8:54 pm
Location: Virginia Beach, VA

p-64 firing pin

Post by irishbob979 »

I'm still getting the run around from the machine shop guy - I really think the perceived liability issue is the problem. I have received a favorable response from Harrington Products - they currently manufacture parts for the CZ 52. The owner says he is interested in making P 64 pins - he asked for a sample. The only problem is that he's in Indiana. Any members in that area that would be willing to drop by and provide a sample? This looks like our best option - this guy already manufactures gun parts and is willing.



Harrington Products
7726 State Road 26 East
Lafayette IN 47905
+1-765-589-9112
harringtonproducts@fpnmail.com
Last edited by irishbob979 on January 13th, 2010, 10:40 pm, edited 1 time in total.
normsutton
Global moderator
Global moderator
Posts: 3575
Joined: February 26th, 2006, 6:59 am
Location: LAKELAND FL.

p-64 firing pin

Post by normsutton »

brock123

try your local range ,every one around here is 50 to 75 but the local range dose it 30 ,

NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976

ImageImage
7point62fmj
Junior member
Posts: 18
Joined: January 7th, 2010, 1:03 pm

p-64 firing pin

Post by 7point62fmj »

irishbob979 wrote:I'm still getting the run around from the machine shop guy - I really think the perceived liability issue is the problem.
Wow you would think with the way the economy is today that they would be jumping at any chance to make money. Maybe it’s not as bad out there as the media leads me to believe.

I know there are a few place on the internet that already makes custom firing pins. IF you get no where I will see if I can hit them up. What we realy need is a CAD drawaing of this pin. That way no one has to send there pin in.
Last edited by 7point62fmj on January 13th, 2010, 11:47 pm, edited 1 time in total.
donnerwetter58
Senior member
Senior member
Posts: 217
Joined: March 24th, 2007, 7:50 am
Location: SW Ohio

p-64 firing pin

Post by donnerwetter58 »

I'll be in Indiana next week and within 35 miles of Harrington Products. I could stop by if you don't find a CAD drawing before then.
I have both a round and triangle hammer version I could pull samples from. I don't intend to leave any parts with them though.
Any thoughts of having them make safeties as well? This is the other part with noted failures.
If Harrington does these parts they will most likely market them too. This would eliminate any personal investment.
normsutton
Global moderator
Global moderator
Posts: 3575
Joined: February 26th, 2006, 6:59 am
Location: LAKELAND FL.

p-64 firing pin

Post by normsutton »

Don
good idea there are more safeties brake than firing pins,

thank you

NORM
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976

ImageImage
dom
Member
Member
Posts: 79
Joined: June 24th, 2009, 4:26 pm
Location: Texas

p-64 firing pin

Post by dom »

brock123 wrote: Wish I could find a reasonable FFL a little closer to home. I checked a few place and they all wanted 75 bucks. The place where I grew up is only 25 but 2 hours away.
Brock- Gunbroker has a neat service on their website they call "dealer network." Just type in your zipcode and a listing comes up of local dealers. Alot of them also list their fee.
http://www.gunbroker.com/FFL/DealerNetwork.aspx
brock123
Member
Member
Posts: 53
Joined: January 10th, 2010, 10:32 pm
Location: Lansing, MI

p-64 firing pin

Post by brock123 »

Nice never looked at that feature on there and it has a few at 20 and 25.
irishbob979
Member
Member
Posts: 74
Joined: October 12th, 2009, 8:54 pm
Location: Virginia Beach, VA

p-64 firing pin

Post by irishbob979 »

Went and retrieved my firing pin today. The machine shop decided that the perceived liability issue was not worth the risk. I guess Harrington Products is the most viable option. Sorry I couldn't get this done.
donnerwetter58
Senior member
Senior member
Posts: 217
Joined: March 24th, 2007, 7:50 am
Location: SW Ohio

p-64 firing pin

Post by donnerwetter58 »

irishbob,
PM with any details of your conversation with Harrington. A contact name would be appreciated.
Thanks,
Dave
irishbob979
Member
Member
Posts: 74
Joined: October 12th, 2009, 8:54 pm
Location: Virginia Beach, VA

p-64 firing pin

Post by irishbob979 »

Dave,

My personal is dcplug@msn.com - work is robert.conklin@ngc.com
donnerwetter58
Senior member
Senior member
Posts: 217
Joined: March 24th, 2007, 7:50 am
Location: SW Ohio

p-64 firing pin

Post by donnerwetter58 »

The current plan is to visit Harrington Products next week to show them a sample of a firing pin and safety.
I tore down both of my P-64s. One is a 1971 round hammer and the other is a 1976 triangle hammer. Both firing pins were for all practical purposes identical. The 1971 measured 1.837" (46.66 mm) overall length. The point to the spring shoulder was 1.364"
(34.65 mm). The 1976 measured 1.835" (46.61 mm) OAL and point to shoulder was 1.364" (34.65 mm). The overall length differed by only .002" (.05 mm).
Would anyone else care to measure their firing pins to see what variations we find?
Thanks,
Dave
Post Reply