Camo Grips, photos posted...
Camo Grips, photos posted...
Just getting in line........Havn't posted here in a while.
I would also love to purchase a pair, or two, of those camo grips!!!
I think the black/white swirl looks the best but honestly, any variation would be an excelent improvement to my slightly ill-fitting thumbrest grips I have now.
Please add me to the list!!!!
I would also love to purchase a pair, or two, of those camo grips!!!
I think the black/white swirl looks the best but honestly, any variation would be an excelent improvement to my slightly ill-fitting thumbrest grips I have now.
Please add me to the list!!!!
-
- Forum supporter
- Posts: 1221
- Joined: February 5th, 2007, 8:52 pm
- Location: Portland Oregon
Camo Grips, photos posted...
Man, I really like the black and white set in the lower right hand corner, very nice.
Gunney Rabbit
Gunney Rabbit
Camo Grips, photos posted...
I will have some good photos of grips tomorrow of 3 variations of camo grips I have done. I will be able to do most colors. I think they look pretty good on the P-64 and the finish is tough and I can do many color variations. I have had all the equipment already and honestly redoing these grips makes them look factory new and modern.
Just to be upfront here with everyone.. I will be doing this for a limited time basis only. After doing several already it is honestly not worth my time in doing them I have discovered. Kinda labor intensive for the relatively small project it is. Anyway I just feel like doing something that some of you guys might like. If know one cares for them then it is really no big deal really. I mean that... It took me 4 hours for 3 grips and another hour for clean up. Anyway if you want some than I will be happy to do yours for you for a small fee but only will do at the most 20 grips. I will make a list of those interested. Anyway thanks for reading.
-Troy
Just to be upfront here with everyone.. I will be doing this for a limited time basis only. After doing several already it is honestly not worth my time in doing them I have discovered. Kinda labor intensive for the relatively small project it is. Anyway I just feel like doing something that some of you guys might like. If know one cares for them then it is really no big deal really. I mean that... It took me 4 hours for 3 grips and another hour for clean up. Anyway if you want some than I will be happy to do yours for you for a small fee but only will do at the most 20 grips. I will make a list of those interested. Anyway thanks for reading.
-Troy
-
- Veteran member
- Posts: 650
- Joined: November 19th, 2006, 8:28 pm
- Location: michigan, down the river
Camo Grips, photos posted...
I think I'd like to get in on the limited edition TTH grip. Looking forward to seeing more of your work Troy. The refinishing and holster work, along with your manuals have been outstanding.
Camo Grips, photos posted...
I may go for one
Camo Grips, photos posted...
Ok here is goes....
Completely refinished grips... Starting with your grips being...
-Degreased
-Aluminum oxide blasted 120grit
-Washed again
-3 Coats of base Duracoat finish
-Either 2 color or 3 color camo scheme. (colors shown are just a few of the colors I can do)
Cost is $22 including return shipping.
Incase you don't know about Duracoat from Lauer Custom Weaponry, I will tell you that it is one of the toughest firearm finishes you can get. I have done it on many pistols including many guys here and the Makarov board. Almost all my personal guns are Duracoated and it is far tougher than any factory finish I have experience with. Once your grip is done you will not be able to remove the color with cleaning solvent. The only way to sort of remove it is to reblast it and re-duracoat it another color. It will not chip, peal or flake. It is damn tough.
Here are photos, pm me if you want your grips done.
-Troy
Before shot...
After Sand Blasting
Refinished in satin-black
After sandblasting with alum-oxide 120 grit
Desert Tan and Black
OD Green and Black
OD Green and Black and Desert Brown
Additional Shot
That P-64 was blasted and parkerized and duracoated and for about 6 months now been in and out of a holster many times every day... literally every day and I notice know wear.
Completely refinished grips... Starting with your grips being...
-Degreased
-Aluminum oxide blasted 120grit
-Washed again
-3 Coats of base Duracoat finish
-Either 2 color or 3 color camo scheme. (colors shown are just a few of the colors I can do)
Cost is $22 including return shipping.
Incase you don't know about Duracoat from Lauer Custom Weaponry, I will tell you that it is one of the toughest firearm finishes you can get. I have done it on many pistols including many guys here and the Makarov board. Almost all my personal guns are Duracoated and it is far tougher than any factory finish I have experience with. Once your grip is done you will not be able to remove the color with cleaning solvent. The only way to sort of remove it is to reblast it and re-duracoat it another color. It will not chip, peal or flake. It is damn tough.
Here are photos, pm me if you want your grips done.
-Troy
Before shot...
After Sand Blasting
Refinished in satin-black
After sandblasting with alum-oxide 120 grit
Desert Tan and Black
OD Green and Black
OD Green and Black and Desert Brown
Additional Shot
That P-64 was blasted and parkerized and duracoated and for about 6 months now been in and out of a holster many times every day... literally every day and I notice know wear.
Last edited by brigade on October 13th, 2007, 9:52 pm, edited 1 time in total.
Camo Grips, photos posted...
HOLY CRAP!!!
Just a few of the colors?????? enlighten us oh king of the duracoat
Just a few of the colors?????? enlighten us oh king of the duracoat
Last edited by trent on October 13th, 2007, 10:01 pm, edited 1 time in total.
-
- Member
- Posts: 134
- Joined: December 16th, 2006, 2:10 pm
- Location: Ohio
Camo Grips, photos posted...
I'm in........ but what color??????
Camo Grips, photos posted...
I have many stock colors however I know how to blend colors to acheive custom ones. My stock colors are Woodland tan, Woodland Green, Matte Black, HK(satin black) Desert Brown, Coyote Tan, ACU Green/Gray, OD Green, Vltor Flat Dark Earth, Gray Green.
Color samples can be viewed here.
http://www.lauerweaponry.com/duracoatco ... tegory=220
-Troy
Color samples can be viewed here.
http://www.lauerweaponry.com/duracoatco ... tegory=220
-Troy
Camo Grips, photos posted...
DOOOOOOOOD !!! That Bottom gun is AWESOME LOOKING !! Green and Black Looks Great also ! Great Job Man. G
Last edited by garry on October 18th, 2007, 12:09 pm, edited 1 time in total.
Camo Grips, photos posted...
You are the man! Looks great! I ask my wife if I could send the original "Bubbaized" grips to you for refinish. I will have to see if they can be fixed a bit before sending them to you though. I will post pics if I can figure out if I can upload from my computers hard drive, can this be done? Good looking grips Troy,
Timbo
Timbo
-
- Global moderator
- Posts: 3575
- Joined: February 26th, 2006, 6:59 am
- Location: LAKELAND FL.
Camo Grips, photos posted...
NORMSUTTON@AOL.COM
N.R.A. LIFE MEMBER 1976
N.R.A. LIFE MEMBER 1976
Camo Grips, photos posted...
carguy
In my area in Ohio there is a local range that has a "gun club" called the "pink pistols" this is (I'm told) a mens club.
In my area in Ohio there is a local range that has a "gun club" called the "pink pistols" this is (I'm told) a mens club.
Camo Grips, photos posted...
I wouldn't take that bet???
Camo Grips, photos posted...
If those grips are still up for grabs I would really love a set of the black and white ones. I am sorry but I am not able to check in here every day could you hit me with a message or use my email? I would be happy to send a check tomorrow.