Search found 60 matches

by Cyndicalist
July 17th, 2019, 1:46 am
Forum: Reloading
Topic: Crimping with Lee 3 die set
Replies: 5
Views: 98

Re: Crimping with Lee 3 die set

Thanks again.
by Cyndicalist
July 15th, 2019, 12:52 am
Forum: Reloading
Topic: Crimping with Lee 3 die set
Replies: 5
Views: 98

Re: Crimping with Lee 3 die set

I have a few hundred once fired brass. What's the best way to get them to the same size? What size do I pick? I'm about to pick up the Lee makarov case length gage as I already have the cutter, but if you have any advice I'd find it most helpful. Thanks Nick...for answering all my inane questions. :)
by Cyndicalist
July 11th, 2019, 5:07 pm
Forum: Reloading
Topic: Crimping with Lee 3 die set
Replies: 5
Views: 98

Re: Crimping with Lee 3 die set

Thanks. That's super helpful. Appreciate it.
by Cyndicalist
July 11th, 2019, 1:27 am
Forum: Reloading
Topic: Crimping with Lee 3 die set
Replies: 5
Views: 98

Crimping with Lee 3 die set

Hello! I'm just starting to reload and bought the lee 3 die set with the set/crimp being one die. Have folks had good results seating and crimping? Should I set it to seat only then get a crimp die? What should I do in the mean time? Also, anyone have any reloading stuff gathering dust they could gi...
by Cyndicalist
June 29th, 2019, 2:24 am
Forum: Reloading
Topic: 9x18 ultra brass able to be reloaded to Mak?
Replies: 5
Views: 128

Re: 9x18 ultra brass able to be reloaded to Mak?

Noted.

Thanks. Will do.
by Cyndicalist
June 27th, 2019, 8:58 pm
Forum: Reloading
Topic: 9x18 ultra brass able to be reloaded to Mak?
Replies: 5
Views: 128

Re: 9x18 ultra brass able to be reloaded to Mak?

That's super helpful. Thanks. I have 50 unfired ultra that someone saved for me from an estate sale. He confused ultra for mak.

If I can remove the bullet and somehow use the primed case, that'd be great.
by Cyndicalist
June 20th, 2019, 10:53 pm
Forum: Reloading
Topic: 9x18 ultra brass able to be reloaded to Mak?
Replies: 5
Views: 128

9x18 ultra brass able to be reloaded to Mak?

Anyone have advice on turning 9x18 ultra brass into 9x18 makarov?

I bought a ton of 9x18 ammo and components, then discovered a few 9x18 ultra brass and ammo.

Best,

C.
by Cyndicalist
May 13th, 2019, 12:04 am
Forum: Reloading
Topic: Another reloading noob
Replies: 3
Views: 167

Re: Another reloading noob

I have had good luck using Berry's 95 grain FMJs and the Lee three die set. You set the seating die to crimp and seat in one operation, if desired. I use a light taper crimp. My handloads feed perfectly in my P-64s, cycle the guns properly and are consistently more accurate than my shooting abiliti...
by Cyndicalist
May 12th, 2019, 1:32 am
Forum: Reloading
Topic: Another reloading noob
Replies: 3
Views: 167

Another reloading noob

Just starting to reload 9x18 and .223 and 8mm. I'm skimming the old posts. What's folks thoughts about what primers, powder and bullets to use? I ordered some speer and Berrys FMJ bullets. But I think I want to cast my own eventually. Anyone try the cast ones you can buy in bulk? And what about crim...
by Cyndicalist
April 24th, 2019, 11:57 pm
Forum: Modifications, Fixes, and Repairs
Topic: V.07 vs V.05 Polish Iron Grips
Replies: 3
Views: 336

Re: V.07 vs V.05 Polish Iron Grips

There have not been very many updates on the Polish Iron grips around here in general. The last discussion was early this month, and before that October of last year. http://www.p64resource.com/forum/viewtopic.php?f=3&t=6074&start=45 They have been selling, and normally the absence of feedback on a...
by Cyndicalist
April 20th, 2019, 2:40 am
Forum: Modifications, Fixes, and Repairs
Topic: Wolff 18 lb Hammer Spring dangerous
Replies: 6
Views: 553

Re: Wolff 18 lb Hammer Spring dangerous

I kept the stock hammer spring because the SA with it is perfect, around 3 pounds and crisp. The DA is 24 but I don't care much. I did put in a 22# recoil spring and a new firing pin spring, both function very well, but can't feel difference.
by Cyndicalist
April 13th, 2019, 9:52 am
Forum: Modifications, Fixes, and Repairs
Topic: Safety broke, bought eBay CNC replacements
Replies: 15
Views: 842

Re: Safety broke, bought eBay CNC replacements

Another guy in Poland is selling originals right for on Ebay for 50 dollars.

A bit steep if you ask me. But I'd pay if mine busted, that's for sure.
by Cyndicalist
December 1st, 2018, 5:38 am
Forum: General P-64 Discussion
Topic: Police training models
Replies: 4
Views: 455

Re: Police training models

The "school" ones, right?

I guess more specifically I want to know if I can buy one for parts. Not so much fix the training pistol, but to get some needed extra stuff. By its good to know they can't be fixed themselves.

Thanks!
by Cyndicalist
November 29th, 2018, 10:53 pm
Forum: General P-64 Discussion
Topic: Police training models
Replies: 4
Views: 455

Police training models

Anyone have the skinny in the police models?

I know they are cut open on the barrel, but can they operate with a new barrel? Do you need to DROS them?

Are the other parts usable?

Any insight is helpful, I got offered 2 for 200 and want to do it if it's a good deal.

Thanks folks!