Search found 8 matches
- November 5th, 2018, 6:41 pm
- Forum: General P-64 Discussion
- Topic: Recoil
- Replies: 16
- Views: 13724
Re: Recoil
^^^ What he said; I'm well satisfied with mine. Reported problems with the PI grip are few, and are corrected with the solutions above or a quick line to Russ. No they’re really not “few”, if you look on the posts there’s quite a bit more than a “few”. This’s isn’t to say that PI grips aren’t a qua...
- May 11th, 2018, 9:33 am
- Forum: General P-64 Discussion
- Topic: trigger bar binding with polish iron grips
- Replies: 23
- Views: 18500
Re: trigger bar binding with polish iron grips
Russ seems to be a solid guy, in the couple times we’ve communicated he might take a day or two to get back but he does get back to you. I believe he does this on the side and isn’t his primary job.
- May 7th, 2018, 11:43 pm
- Forum: General P-64 Discussion
- Topic: trigger bar binding with polish iron grips
- Replies: 23
- Views: 18500
Re: trigger bar binding with polish iron grips
I can't find and edit my response I made a few minutes ago but I did find this in the installation instructions: "The grip is flexible. And under normal use. And even a very hard grip. The grip will not disturb the trigger bar. However you can disturb the trigger bar by pressing directly on th...
- May 7th, 2018, 11:38 pm
- Forum: General P-64 Discussion
- Topic: Recoil pain. Am I holding it wrong?
- Replies: 38
- Views: 30981
Re: Recoil pain. Am I holding it wrong?
Rider, try as I might, I cannot get these grips to budge. Think I'll need a razor knife to get them off. For the time being, it's just sitting here on my desk, and from time to time I try to budge them. I've watched the part of the video where he takes them off, and stood baffled as he does it easi...
- May 7th, 2018, 11:22 pm
- Forum: General P-64 Discussion
- Topic: trigger bar binding with polish iron grips
- Replies: 23
- Views: 18500
Re: trigger bar binding with polish iron grips
I had a similar problem and spoke with Russ vis e-mail and he said this was a common problem and why he’s going to a semi rigid design but he wasn’t sure they were going to become available as he still had them out being beta tested. He did offer to take them back and refund the money but unfortunat...
- November 14th, 2017, 10:58 pm
- Forum: Modifications, Fixes, and Repairs
- Topic: Hammer binding caused Polish Iron grips?
- Replies: 5
- Views: 5502
Hammer binding caused Polish Iron grips?
So I tried out my pistol with the new grips and ran into trouble with the hammer resetting after firing. It only happens when a magazine is inserted so I’m wondering if a linkage is being pushed out in to the rubber grip and binding. Has anyone else run into this? The grips fit great and really soak...
- September 10th, 2017, 6:58 pm
- Forum: General P-64 Discussion
- Topic: Marshal grips
- Replies: 0
- Views: 3561
Marshal grips
Has anyone had issues? I got mine fitted by a gun smith and they look good but they're almost too big for my hand and make the pistol sit cockeyed in my hand to reach the trigger like there needs to be material removed from right sight where my trigger finger rides and the beaver tail where it sits ...
- September 10th, 2017, 1:12 am
- Forum: Modifications, Fixes, and Repairs
- Topic: Hello
- Replies: 2
- Views: 3391
Hello
I've learned a lot by reading these threads. Thanks for all the wisdom you've all been putting out there.