Search found 8 matches

by Jimbo
November 5th, 2018, 6:41 pm
Forum: General P-64 Discussion
Topic: Recoil
Replies: 16
Views: 13257

Re: Recoil

^^^ What he said; I'm well satisfied with mine. Reported problems with the PI grip are few, and are corrected with the solutions above or a quick line to Russ. No they’re really not “few”, if you look on the posts there’s quite a bit more than a “few”. This’s isn’t to say that PI grips aren’t a qua...
by Jimbo
May 11th, 2018, 9:33 am
Forum: General P-64 Discussion
Topic: trigger bar binding with polish iron grips
Replies: 23
Views: 17973

Re: trigger bar binding with polish iron grips

usagi wrote: May 11th, 2018, 5:56 am emailed polish iron grips last friday about the problems, still no response.
Russ seems to be a solid guy, in the couple times we’ve communicated he might take a day or two to get back but he does get back to you. I believe he does this on the side and isn’t his primary job.
by Jimbo
May 7th, 2018, 11:43 pm
Forum: General P-64 Discussion
Topic: trigger bar binding with polish iron grips
Replies: 23
Views: 17973

Re: trigger bar binding with polish iron grips

I can't find and edit my response I made a few minutes ago but I did find this in the installation instructions: "The grip is flexible. And under normal use. And even a very hard grip. The grip will not disturb the trigger bar. However you can disturb the trigger bar by pressing directly on th...
by Jimbo
May 7th, 2018, 11:38 pm
Forum: General P-64 Discussion
Topic: Recoil pain. Am I holding it wrong?
Replies: 38
Views: 29453

Re: Recoil pain. Am I holding it wrong?

Rider, try as I might, I cannot get these grips to budge. Think I'll need a razor knife to get them off. For the time being, it's just sitting here on my desk, and from time to time I try to budge them. I've watched the part of the video where he takes them off, and stood baffled as he does it easi...
by Jimbo
May 7th, 2018, 11:22 pm
Forum: General P-64 Discussion
Topic: trigger bar binding with polish iron grips
Replies: 23
Views: 17973

Re: trigger bar binding with polish iron grips

I had a similar problem and spoke with Russ vis e-mail and he said this was a common problem and why he’s going to a semi rigid design but he wasn’t sure they were going to become available as he still had them out being beta tested. He did offer to take them back and refund the money but unfortunat...
by Jimbo
November 14th, 2017, 10:58 pm
Forum: Modifications, Fixes, and Repairs
Topic: Hammer binding caused Polish Iron grips?
Replies: 5
Views: 5371

Hammer binding caused Polish Iron grips?

So I tried out my pistol with the new grips and ran into trouble with the hammer resetting after firing. It only happens when a magazine is inserted so I’m wondering if a linkage is being pushed out in to the rubber grip and binding. Has anyone else run into this? The grips fit great and really soak...
by Jimbo
September 10th, 2017, 6:58 pm
Forum: General P-64 Discussion
Topic: Marshal grips
Replies: 0
Views: 3090

Marshal grips

Has anyone had issues? I got mine fitted by a gun smith and they look good but they're almost too big for my hand and make the pistol sit cockeyed in my hand to reach the trigger like there needs to be material removed from right sight where my trigger finger rides and the beaver tail where it sits ...
by Jimbo
September 10th, 2017, 1:12 am
Forum: Modifications, Fixes, and Repairs
Topic: Hello
Replies: 2
Views: 3303

Hello

I've learned a lot by reading these threads. Thanks for all the wisdom you've all been putting out there.