Search found 1347 matches

by juniustaylor
June 21st, 2017, 9:58 pm
Forum: General P-64 Discussion
Topic: Made some videos
Replies: 68
Views: 37404

Re: Made some videos

Fortunately I never did have to make that video! I also no longer have mine. I traded it for a Ruger Mark 2 6" BBL some years back. However, in very glad that people are still finding them useful and relevant. Not sure if they still are, but at the time they were the ONLY videos online to cover ever...
by juniustaylor
June 6th, 2015, 1:13 am
Forum: Reloading
Topic: Looking for moral support on .270 Win 130gr SST load
Replies: 1
Views: 1975

Re: Looking for moral support on .270 Win 130gr SST load

This was the 3-shot group with the Federal Power-Shok 130gr ammo from Walmart.
by juniustaylor
June 6th, 2015, 1:10 am
Forum: Reloading
Topic: Looking for moral support on .270 Win 130gr SST load
Replies: 1
Views: 1975

Looking for moral support on .270 Win 130gr SST load

I've been going back and forth on what kind of load to use in my Remington 700 BDL .270 Win. I bought some Hornady 130gr SST bullets earlier this year as that's what I plan on shooting from it. I had some 130gr Federal Power-Shok that I bought from Walmart when I first bought the rifle from the olde...
by juniustaylor
June 5th, 2015, 11:20 pm
Forum: General P-64 Discussion
Topic: No Loaded Chamber Indicator - Thoughts?
Replies: 12
Views: 3478

Re: No Loaded Chamber Indicator - Thoughts?

Glad you got that sucker back in there!!
by juniustaylor
June 5th, 2015, 11:15 pm
Forum: Reloading
Topic: post some your pet 9 X 18 loads
Replies: 47
Views: 25880

Re: post some your pet 9 X 18 loads

HassoBoxhead
Lyman 48th Lists:
(min)2.3gr = 616 fps
(MAX)3.4gr = 900 fps
Seating = 0.970" OAL
by juniustaylor
June 5th, 2015, 11:14 pm
Forum: Reloading
Topic: Need a Recipe
Replies: 2
Views: 1918

Re: Need a Recipe

HassoBoxhead
Lyman 48th Lists:
(min)2.3gr = 616 fps
(MAX)3.4gr = 900 fps
Seating = 0.970" OAL
by juniustaylor
June 4th, 2015, 9:15 pm
Forum: Reloading
Topic: powder coating lead bullets
Replies: 6
Views: 3814

Re: powder coating lead bullets

I've had good success with 158gr .358" PC bullets in a Ruger Vaquero .357 Mag. Loaded them up to almost fullpower jacketed velocity with VihtaVouri N110. I tumbled them around in a ziploc bag for a minute or so by hand. Bake them in a toaster oven for 15 minutes on about 375 degrees. Leading has bee...
by juniustaylor
December 14th, 2014, 2:10 am
Forum: General P-64 Discussion
Topic: Made some videos
Replies: 68
Views: 37404

Re: Made some videos

txbiker, I am glad you found them useful to you. Good luck with the safety, they're a walk in the park.
by juniustaylor
August 24th, 2014, 6:59 pm
Forum: Reloading
Topic: Bought some more stuff.
Replies: 14
Views: 6021

Re: Bought some more stuff.

Alright, my last review on this press was about 2 1/2 years ago. I am happy to report this press is still going strong, no surprise as it's a tank. I have acquired several add-ons for it and I have 9mm Luger, .357 Mag, and .45 ACP complete setups always ready to go. Just drop the shellholder on the ...
by juniustaylor
August 20th, 2014, 10:49 pm
Forum: General P-64 Discussion
Topic: Newbie here. Naive question..
Replies: 7
Views: 3050

Re: Newbie here. Naive question..

Check here - http://p64resource.com/forum/viewtopic.php?f=3&t=4538
A person did do some mill-work and made a hi-viz sight work.

I always applied a white base coat and then a red layer over the white. Helps it stand out, using Tester's model car/plane paint.
by juniustaylor
May 31st, 2013, 1:34 am
Forum: Reloading
Topic: cleaning cases
Replies: 5
Views: 2692

Re: cleaning cases

Also, I don't bother cleaning the primer pockets unless they are somehow super filthy. A standard small pistol primer has around 5,000 PSI (or so I've read) and will blow out most any obstruction much less some carbon from a previous firing. Case trimming should be done after sizing. Otherwise if yo...
by juniustaylor
May 31st, 2013, 1:29 am
Forum: Reloading
Topic: cleaning cases
Replies: 5
Views: 2692

Re: cleaning cases

You could always be like these guys on this Facebook group that I am on. You use this Lemishine / Dawn Dishsoap concoction. You wet tumble them in it, then size them, then tumble them again, then trim them, then tumble them, then prime them, then load them, then tumble them again (in dry media). In ...
by juniustaylor
May 31st, 2013, 1:16 am
Forum: Reloading
Topic: Brass catcher, best $20.00 deal I have gotten
Replies: 8
Views: 3762

Re: Brass catcher, best $20.00 deal I have gotten

Here is the one I made... http://www.p64resource.com/forum/viewtopic.php?f=11&t=4590 It works pretty good. It gets tricky dealing with different handguns because they all seem to eject differently. You usually just have to bend the hoop a little and it'll catch most all the brass then. Cheap to make...
by juniustaylor
March 5th, 2013, 11:31 am
Forum: General P-64 Discussion
Topic: Made some videos
Replies: 68
Views: 37404

Re: Made some videos

The recoil spring will come with a (40%) stronger firing pin spring. The idea is that the original firing pin spring is "worn" out and this extra power firing pin spring will help get the firing pin retracted into the slide faster so as to reduce the possibility of the firing pin snagging and draggi...
by juniustaylor
March 5th, 2013, 1:23 am
Forum: General P-64 Discussion
Topic: Made some videos
Replies: 68
Views: 37404

Re: Made some videos

I used a 20# recoil spring. It did reduce some of the felt recoil and slightly added a bit more force needed to rack the slide but not that much. I never paid attention to it anyway. I liked the 17# mainspring. It really lowered the DA trigger pull. It did further lighten the SA trigger pull. Didn't...